If you
are trying to rebuild the STD OEM Honda RS125/250 calipers, there is no piston kit available
for these but one of our Brembo importers came up with this seal kit.
The
full race versions from Brembo are rebuild-able and they would have the name
Brembo in Red printed on them. see 20.4756.62
on the same page.
The OEM production units have silver painted logos or no paint at all.
The
120.2799.50 pistons in the kits below will fit the
bore but are not the correct depth so they should not be used in the
OEM replacement calipers.
Cost of the OEM calipers are a $200 or
less replacement cost while the full race units are $600 and up. So, they
(the OEMs or Brembo) have decided that if the OEM calipers get to a point of
needed new pistons, they should be replaced.
|
 |
20.4756.62
30/34 Caliper 2 Piece Billet GP- Right -Front Brembo 40mm Bolt Center
Brembo billet GP racing caliper that has been a performance upgrade for
decades. This brembo caliper is about 1/4 lb lighter than the cast caliper,
and stiffer. The brembo billet GP caliper is designed for superior pad
retraction, and because of this, if a favorite for serious racers.
 |
 |
120.2799.50
30/34 Piston/Seal kit for 4 Piston GP Caliper - Gold Line
Calipers Brembo

For 20.4756.62 Caliper above only |
 |
BREMBO 19
RCS RADIAL BRAKE MASTER CYLINDER
The Brembo radial master cylinder has effectively
revolutionized motorcycle braking systems over the past ten years. Designed
originally for use on Racing machines, it has become more and more popular
over time for Super Sport, and even Naked bikes, while retaining the
identity of an out-and-out racing component, still used today in MotoGP
competition. For more information CLICK
HERE
110.A263.10
$365.00
 |
 |
10.4760.75
19x18 Brake Master Cylinder with Folding Lever
Forged race type master cylinder with pre-installed folding brake lever.
 |
10.4760.85
16x18 Brake Master with Folding Lever
Forged race type master cylinder with pre-installed folding brake lever.
 |
 |
10.4760.80
16x18 Brake Master Cylinder- Brembo Radial Pump
Master cylinder for single caliper front brake set up. When ordering a
replacement lever, be sure to match the pivot length of the lever with the
pivot length of the master cylinder (2nd number)
 |
10.4760.70
19x18 Brake Master Cylinder- Brembo Radial Pump
Radial racing master cylinder for dual disc brake fornt ends. The 19x20
model gives the stiffest brake lever, the 19x18 lever provides a little more
feel, and a lighter pull on the lever is required. When ordering a
replacement lever, be sure to match the pivot length of the lever with the
pivot length of the master cylinder (2nd number)
 |
10.4760.60
19x20 Brake Master Cylinder- Brembo Radial Pump
Radial racing master cylinder for dual disc brake front ends. The 19x20
model gives the stiffest brake lever, the 19x18 lever provides a little more
feel, and a lighter pull on the lever is required. When ordering a
replacement lever, be sure to match the pivot length of the lever with the
pivot length of the master cylinder (2nd number)
 |
 |
110.4266.60
Repair Kit- Brembo Radial Pump Master Cylinder
Crash repair kit for the race series radial pumps. This kit contains the
aluminum top hat and push rod that always gets bent. Keep one in the spares
kit  |
 |
110.4594.60
Long Lever 20mm Kit Brembo
(can use Honda 53175-NX5-680)
 |
110.4594.61
Long Lever 18mm Kit Brembo
 |

110.5231.16
18mm Radial Folding lever kit
Folding lever for " X 18 " size radial brake or clutch master cylinders
 |

110.7264.32
18mm Radial Short Lever
Brembo short lever for radial master cylinder. Lever is 25mm shorter than
standard length lever.
 |
|

10.5107.10
Spare Adjustment Knob

A51.1010.46
Roll pin to attach knob to radial master cylinders
 |

105.3387.10
Bleeder Screw for New Style F08 Brembo

Thread - M10x1.0
Length Under Hex - 16mm
Wrench Size 11mm
Color - Silver |

105.3387.60
Bleeder Set for GPmk3 Billet Caliper and radial pump
 |

A63.1010.90
Clip for Brembo Cast Iron Floating Brake Rotor
 |

A34.0400.14
Washer for Brembo Cast Iron Floating Brake Rotor - .5mm thick, 20mm OD x
14mm ID
 |

120.3840.81
Pin for 30/34 Billet Caliper Brembo
 |

VF1/1
M10x1.0 Banjo + Bleeder
 |

VF1/2-28
Double Bolt M10x1x28mm

VF1/2-30
Double Bolt M10x1x30mm

|

06.2228.22
Double Banjo Bolt M10x1.0 Steel For Brembo TBD
 |

06.2228.45
Single Banjo Bolt M10x1.0x19 Steel For Brembo
 |

09-29001-00 Aluminum Washers
Washers for aluminum banjo bolts
 |

06.2196.13
Copper Washer 10mm For Brembo - Crush washer for use with steel banjo bolts.
Priced each, but only sold in packages of 10.
 |

10.4446.50
15cc Reservoir Remote 45 fitting - Brembo, 15cc resorvoir for rear brake or
clutch applications.
 |

10.4446.40
15cc Reservoir Remote Straight Fitting - Brembo 15cc resorvoir for rear
brake or clutch applications.
 |

10.4446.30
30cc Reservoir Flange Mount- Screw Cap for front
brake applications - Brembo
 |
 |
19.6371.26
6mm Clear Tubing For Brake Fluid - Brembo Size
This is the only clear tubing on the market that will not sweat, crack,
discolor or harden. Tubing is sold by the foot.
 |
|
|