|
|
|
|
|
MD250 Foot peg set OEM
|
|
NOS foot peg set for 2009 Moriwaki MD250H. Can be made to fit RS125, NSF250r, and 2008 MD250H with use of own shortened bolt. This was the OEM setup for the 2009 model.
|
|
|
|
|
|
|
|
Fuel cap - used
|
|
Fuel cap for Honda RS125 (2000+), NSF250R and some of the RS250 models Comes with gasket.
Great to have in the spares box for that one time you forget to tighten yours down and get crotch full of race gas!
|
|
|
|
|
|
|
|
Hjelm Sprocket carrier wrench
|
|
Used Hjelm sprocket carrier holder. Works on Talon sprocket carrier and makes changing them significantly easier.
|
|
|
|
|
|
|
|
Ohlins Spring
|
|
Used Ohlins spring - check fitment 1093-14/60 LD97
|
|
|
|
|
|
|
|
Fork springs used - RS125, NSF250, MD250
|
|
Used front fork springs. One size softer than stock RS125 springs, 2 sizes softer than NSF stock springs. SPRING, FRONT FORK (k=0.6)
|
|
|
|
|
|
|
|
Front Fender
|
|
New Hotbodies brand front fender for Honda RS125. Fits all years from 1995 on,but is styled after the 2004 model bodywork. Never been drilled or mounted on a bike. Will also fit MD250H and NSF250R.
|
|
|
|
|
|
|
|
Hjelm brand NOS left rearset
|
|
New old stock Hjelm left side rearset. Standard length. Replaces 50600-nx4-770
Limited to stock on hand.
|
|
|
|
|
|
|
|
New Eibach rear spring - RS125/NSF/MD
|
|
Rear Eibach spring for RS125/MD/NSF. See picture for specs
|
|
|
|
|
|
|
|
Moto3 Crash spares
|
|
Several new and used bits that are good to have in your spares bin for crashes and such. Will fit all NSF250R, MD250H, and 95+ Honda RS125
Brake lever, fairing side mounts, clutch perch, axle nut and slider
|
|
|
|
|
|
|
|
Used rearsets - RS125/NSF/MD
|
|
Used rearsets for Honda RS125, NSF250R, and even should fit the MD250H. Look closely to make sure they work for you. These are sold as a pair and should work on either side of the bike.
These would make great cheap crash spares!
|
|
|
|
|
|
|
|
Swingarm Tool
|
|
New old stock - swingarm tool for RS125. Made by Hjelm, and not available anymore. Same as Honda part: 07908-4690002
|
|
|
|
|
|
|
|
Used Front Rotor
|
|
Used front rotor - fits RS125 (NX4 and NF4), MD250, NSF250R, RS250 (NX5)
|
|
|
|
|
|
|
|
Suspension linkage
|
|
Suspension linkage for Honda RS125 ('95-on) and all NSF250R 52460NX4-000 used for mockup only. Otherwise it's brand new. Comes with bolts and teflon washers.
|
|
|
|
|
|
|
|
Used Front Rotor
|
|
Used front rotor - fits RS125 (NX4 and NF4), MD250, NSF250R, RS250 (NX5)
|
|
|
|
|
|
|
|
Brake pedal - RS125, MD250, NSF250R
|
|
Used PEDAL COMP BRK. Looks brand new. Likely removed from a new bike. Fits '95 on RS125, MD250H, and NSF250R
|
|
|
|
|
|
|
|
NOS Honda swingarm castle nut tool
|
|
NOS Honda swingarm castle nut tool - 07908-4690002
|
|
|
|
|
|
|
|
NOS Galfer rear wave rotor - fits NSF250r, RS125, and MD250H - weight 11oz
|
|
Galfer rear wave rotor - fits NSF250r, RS125, and MD250H - weight 11oz
|
|
|
|
|
|
|
|
RS125/NSF250R/MD250H Sprocket with bearing carrier built in. Comes with Bolts and nuts to fit dampers. You will need the spacer and collar to complete install. BA25-01 and BA25-02
|
: $172.95 Sale Price: $115.00 Save $57.95!
|
|
|
RS125/NSF250R/MD250H Sprocket with bearing carrier built in. Comes with Bolts and nuts to fit dampers. You will need the spacer and collar to complete install. BA25-01 and BA25-02
|
|
|
|
|
|
|
|
ALUMINUM CLIP ON BAR SET W/CAPS (94- RS125/ TZ125 - 44mm ID - 15�ANGEL )
|
: $157.96 Sale Price: $120.00 Save $37.96!
|
|
|
ALUMINUM CLIP ON BAR SET W/CAPS (94- RS125/ TZ125 - 44mm ID - 15�ANGEL )
|
|
|
|
|
|
|
|
Used NX7 mode switch
|
|
Used mode switch. Came off of a working bike. Select between fast and faster!!
|
|
|
|
|
|
|
|
Clipon set - nos
|
|
Clipon set for Honda RS125 ('95-on) and all NSF250R 53110-NX4-000 and 53120-NX4-000 used for mockup only. Otherwise they are brand new. Would make a great emergency set of spares.
|
|
|
|
|
|
|
|
RS125 Swingarm - needs repair
|
|
RS125 swingarm. Needs minor repair as spool mount came off in crash. Needs patch and new spool welded on. Otherwise, ready to go.
|
|
|
|
|
|
|
|
NOS Hjelm right rearset +3cm, shift lever, footpeg
|
|
NOS Hjelm - Honda RS125 and NSF250R Step plate, fits left side, +3cm length Battle shift lever, and footpeg included
|
|
|
|
|
|
|
|
Sprocket Carrier 3-pack
|
|
Like new condition - Intuitive Race Products brand sprocket carriers. 3-pack. Fit '95+ Honda RS125, and all MD250H racebikes. Use RS125 or dual pattern sprockets and these work on all NSF250R bikes as well.
Fit one of these to your 3 most used sprockets and make gearing changes super fast and easy.
|
|
|
|
|
|
|
|
Used Temp Gauge - NX4 and NX7
|
|
Used temperature sensor - fits '95 on Honda RS125 and 2012-2017 NSF250R
|
|
|
|
|
|
|
|
Colts Moto3 Tire Warmers - used
|
|
Very nice condition used Colts brand tire warmers for all Moto3 size rims (TZ125, RS125, NSF250, MD250H)
|
|
|
|
|
|
|
|
MD250 rearsets billet
|
|
Brand new rearsets kit for MD250H. Comes with everything seen in the picture. Also fits all NSF250R, and '95+ Honda RS125.
All original Moriwaki parts except one lever is Battle brand.
|
|
|
|
|
|
|
|
Battle Moto3 Tire Warmers - used
|
|
Very nice condition used Battle brand tire warmers for all Moto3 size rims (TZ125, RS125, NSF250, MD250H)
|
|
|
|
|
|
|
|
Used Sprocket kit
|
|
This is a lightly used set of sprockets with the integrated bearing. These were developed in collaboration with AFAM, so you know the quality is outstanding!
Some sprockets are still new, but most have just minor wear.
Comes with one set of the spacers needed to use this kit on the '95 or newer RS125 Honda, all MD250H, and all NSF250r using RS125 sprockets or dual pattern sprockets. No need for the Talon, IRP, and HRC sprocket carriers when you use this kit.
Kit comes with custom case with aluminum holders to keep things in order. Very nicely made carrier.
|
|
|
|
|
|
|
|
Airbox for NX4 RS125 1995-on - Over the radiator type box
|
|
Airbox for NX4 RS125 1995-on - Over the radiator type box
|
|
|
|
|
|
|
|
RS125 shorty tank - Carbon/Kevlar
|
: $975.00 Sale Price: $749.00 Save $226.00!
|
|
|
Lightly used Carbon/Kevlar fuel tank for '95 and newer Honda RS125. This one is a bit shorter in the back and sloped forward to make it easier for smaller riders to reach the bars. Save 3lbs over the stock tank by swapping to this one. Made by Speed Fiber.
|
|
|
|
|
|
|
|
Rear shock
|
|
Lightly used Reactive brand rear shock for RS125/MD250/NSF250.
|
|
|
|
|
|
|
|
NSF250 Frame and triple-clamps
|
|
Good condition frame and triple clamps from NSF250R.
|
|
|
|
|
|
|
|
Dymag Carbon Fiber Moto3 Rims - used
|
|
Super lightweight used Dymag Carbon Fiber rims for '95+ Honda RS125, all NSF250R, and all Moriwaki MD250h
Seller says he purchased them used with some minor tire machine scuffs and has used them for 5 years now with no problems.
|
|
|